Exactly How To Install A Bath Tub (For Novices).
Click Here To Find Out MoreHere below you can get a good deal of great news in relation to A Step-by-Step Guide to Installing a Bathtub.
Installing a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the task can move immediately; if you have to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need an assistant to vacate the old tub and embeded in the new one. Make certain you have certified yourself for the task and fit trying it. Rather than hiring a service provider to take over a halfway-completed task, it is better to take into consideration employing one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This short article will certainly help you set up a new tub in your washroom if you have currently acquired a new bathtub and also don't require to transform the plan of your previous water system pipes.
Your tools as well as product checklist must consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of removing the existing taps can be rather bothersome due to the restricted gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers are in place in between the tap as well as the sink. Secure the tap in position with the maker offered backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind ought to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the required setting. The wooden boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub up until the level reads degree.
To install faucets, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water supply as well as examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been made use of at least once as this will settle it into its final setting.
Getting ready for the Setup
To start with, the sustaining structure provided with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack rather early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently offered on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about How to Install a Bathtub Yourself? Place a remark directly below. We would be glad to know your views about this content. In hopes to see you back again in the future. Loved our piece? Please share it. Let someone else check it out. I praise you for your time. Visit us again soon.
Prices & Booking